plastic yielding中文是什么意思

• 塑性变形
• 塑性屈服

• "plastic"中文翻译    adj. 1.造型的；塑造的；给与形态的。 2.可塑的， ...
• "yielding"中文翻译    adj. 1.有出产的。 2.易受影响[感化]的；易说服 ...
• "criteria of plastic yielding" 中文翻译 :    塑性变形判别衡准
• "elasto-plastic yielding" 中文翻译 :    弹塑性屈服
• "yielding" 中文翻译 :    adj. 1.有出产的。 2.易受影响[感化]的；易说服的，柔顺的；易屈服的，易让步的。 3.易弯的，会变形的。
• "be of a yielding disposition" 中文翻译 :    性情柔顺
• "bulk yielding" 中文翻译 :    体积屈服
• "criteria of yielding" 中文翻译 :    屈服衡准
• "criterion of yielding" 中文翻译 :    屈服准则
• "delayed yielding" 中文翻译 :    延迟屈服
• "discontinuous yielding" 中文翻译 :    不连续屈服; 间断屈服
• "discontinuousdiscontinuous yielding" 中文翻译 :    不规则降伏
• "distributed yielding" 中文翻译 :    分布屈服
• "elastic yielding" 中文翻译 :    弹性屈服
• "full yielding" 中文翻译 :    全屈服
• "general yielding" 中文翻译 :    全断面降伏; 总变形
• "high-yielding" 中文翻译 :    高产的
• "inealstic yielding" 中文翻译 :    非弹性屈服
• "leg-yielding" 中文翻译 :    顺腿马
• "limit of yielding" 中文翻译 :    屈服极限
• "local yielding" 中文翻译 :    局部屈服
• "microplastic yielding" 中文翻译 :    微塑性屈服
• "nergy yielding" 中文翻译 :    放能的
• "reverse yielding" 中文翻译 :    反向屈服
• "secondary yielding" 中文翻译 :    辅助供水量

• A tension member may fail by plastic yielding .
  拉伸元件可能由于塑性屈伏而破坏。
• Plastic yield test
  塑料变形测试
• The calculation results indicate that the outboard of drum walls fall in plastic yielding at the same time the rising cooling water reaches the height of that point and the yield region becomes narrower and narrower when it comes closer to the circumferential strake weldments , which explains the reason coke drums experience bulging and cracks occur in the weld seams portions of shell to shell after long in service
  计算结果表明：塔壁外侧在冷却水面到达的瞬间进入塑性屈服，筒节中部塑性屈服区较大，当靠近焊缝时塔壁的塑性变形区逐渐缩小直至消失，塔壁塑性屈服区的分布特点解释了塔体长期使用后发生鼓凸变形及简体与焊缝连接处产生裂纹的原因。
• This paper investigated the electrorheological ( er ) characteristics of two suspensions of starch particles ( a ) and aluminosilicate particles ( b ) in silicone oil respectively , and also their transmitting properties on a simulated device of cylindrical er clutch ( erc ) by comparison , only to show that a is a kind of electrorheological fluid ( erf ) with definite plastic yield - point and can be subjected to a narrow voltage range on erc , while b is a kind of pseudo - plastic erf and can be subjected to a wilder voltage range on erc
  本文研究了硅油-淀粉( a ) 、硅油-硅酸铝( b )两种er流体的电流变性能，并通过一套筒式er离合器模拟传动装置，研究且对比了这两种er流体在筒式er离合器上的传输特性。结果表明a是具有塑性屈服点的流体，其在er离合器上有效调速电场范围较小； b是假塑性流体，其在er离合器上有效调速电场范围较宽。
• That the arched roadway with the ratio of 0 . 2 between arch rise and roadway width is substituted fur rectangular roadway can obviously improve the stress state of roadway surrounding rocks , reduce the deformation and the plastic yield area of roadway surrounding rocks , greatly strengthening the stability of roadway surrounding rocks
  采用矢跨比为0 . 2的圆弧拱巷道代替矩形巷道，可显著改善巷道围岩应力状况，减小巷道围岩变形量，减少围岩塑性屈服区域，加强巷道围岩的稳定性。

• plastic yielding перевод